Rubber Gasket

The seal material selection and installation needs to pay attention

by:TaiHai     2020-08-16


the silicone seal material selection and installation note


the silicone seal as one of important parts on industrial equipment, good or bad, directly affect the equipment today, take you to understand that the silicone seal material, as well as the installation need to pay attention to above points.



the silicone seal material selection





the stand or fall of sealing material directly affect the running status of equipment, good sealing material can prolong equipment operation, reduce the leakage, to reduce pollution


to dye.


at present, the commonly used silica gel seal material is a synthetic resin and synthetic rubber.


there is a great variety of synthetic rubber, widely used in the oil resistance, heat resistance, cold resistance, pressure resistance and water resistance, and has the appropriate abrasion resistance, usually the


use temperature roughly: - 40°C- Nitrile rubber and polyurethane rubber.


the nitrile rubber with good + 120 ° C, easy to use metal moulded into any shape of hydraulic seals,


polyurethane rubber with high tensile strength, good oil resistance, heat resistance, cold resistance, pressure resistance and abrasion resistance,


synthetic resin mainly polyformaldehyde, nylon and filled ptfe, etc. Is filled ptfe is widely used, especially suitable for the production of high pressure and ultrahigh pressure rapid movement of the hydraulic cylinder with hydraulic seals.


introduction to the silicone seal installation characteristics and precautions of


seal generally installed in the outside round or circular cross section is rectangular groove seal o-rings, oil resistant, acid-proof, alkali resistance, abrasion, chemical corrosion environment


can still have good sealing, damping effect. Therefore, it is the most widely used seal of hydraulic and pneumatic transmission system. Two o-rings) 。


the characteristics of the silicone seal:





1, excellent performance, high life, 5 - higher than that of dynamic pressure seal service life 10 times than traditional rubber seal products, up to a few times,


under certain conditions, can use a sealed substrate and life;


2, small friction resistance, dynamic and static friction, equality, 1/2 - A quarter? Type sealing ring is the rubber friction, eliminate the low speed, low pressure mobile 'crawl';


3, high wear resistance, sealing surface wear, automatic flexible compensation ability;


4, good self-lubricating properties. Oil free seal;


5, the pressure of work: 0 300 mpa working speed, the working temperature of 15 m/s or less: - 55 - 250;


6, applicable medium: oil, gas, water, mud, oil, emulsion, installation type O sealing ring (1) Installed, type O sealing ring o-ring


requirementsBefore glycol and acid. Notes on


check the following content:


1, the introduction of the perspective of treatment according to the drawings of sharp edge chamfer or rounded;


2, the surface of the inner diameter to remove burrs is clean;


3, seals and components has been apply grease or oil ( To ensure that the media of the compatibility of elastomer, recommended for sealing fluid lubrication)


4, do not use grease, contains solid additives, such as molybdenum disulfide, sulfur, and zinc. ,


manual installation silicone seal:


1, using the tool, no sharp edge;


2, to ensure that the o-ring is not distorted, not overstretch O ring;


3, use the auxiliary function tool to install the o-ring, and ensure that the correct positioning;


4, type O sealing ring sealing glue, do not connect the stretch.


5, install screw, spline, etc. O-rings stretching, there should be a screw, spline, slotting, etc. , you must use the installation of the main shaft. Ingot


the child can be made of metal or plastic with a soft, smooth and no burrs or sharp edges.


6, installing a clamping screw, should be symmetrical, and screw down the screws didn't tighten the direction of the order.


this is a little bit about the silicone seal materials and installation of some of the above considerations, the hope can help you, welcome custom silicone seal.













Wow, this sounds like a bit of a cruel question, but it is a vitally important question to ask yourself if you are struggling with your rubber washers suppliers and you would like to stop the rubber washers problem.
All of the long-term strategies and short-term actions of TaiHai will be molded by a set of core values that are shared by each and every associate.
Do you want to find a provider to get your rubber washers problem settled? If so, we suggest that you give a shot to Foshan taihai rubber and plastic co., LTD. . Visit TaiHai Rubber Products to learn more and contact us.
In order to obtain the most suitable for your rubber washers suppliers, you need to contact qualified suppliers which can produce super quality to your specifications and offer a friendly price.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...